Platinum cured silicone tri-clamp gaskets, 1 inch and 1.5 inch, translucent clear
40RXPX-100-FDA

Tri-Clamp Gasket, Platinum Cured Silicone, 1 to 6 in.

$1.95IN STOCK
Ships in 1 business day
5 sizes, $1.95 to $32.50
SELECT SIZE

ABOUT THIS PART

Platinum cured, FDA compliant silicone gasket for steam, hot water and food contact lines. Not for hydrocarbon extraction. Use Viton for solvent, including isopropyl, and PTFE for cold service.

SPECIFICATIONS

MaterialPlatinum cured silicone
ComplianceFDA compliant
Sizes1, 1.5, 2, 4, 6 in.
Temperature-85 to 450 F (-65 to 232 C)
Clamp torque30 in-lb
Not forButane, propane, heptane, pentane, hexane (rated severe)
IsopropylA, excellent, per Cole-Parmer chemical resistance data
Certification note3P Certz ECR-200031-R0 lists silicone as not acceptable in the extraction system
ReplaceEvery 3 to 6 months
TECHNICAL DETAILS

Platinum cured silicone tri clamp gasket, FDA compliant, in 1, 1.5, 2, 4 and 6 inch, from $1.95. Every size is priced on this page.

Read this before you order. Silicone rates severe against butane, propane, heptane, pentane and hexane. Cole-Parmer chemical resistance data rates it excellent on isopropyl, but it is not a hydrocarbon gasket and N.B. Oler does not recommend it for extraction service. It is on this site because silicone is the right answer for steam, hot water and food contact, and because people ask for it by name.

If you are running solvent, including isopropyl, use Viton. If you are going cold, use PTFE.

Sizes and price

Size Price
1 in $1.95
1.5 in $1.95
2 in $1.95
4 in $3.75
6 in $32.50

The numbers

  • Temperature: -85 F to 450 F (-65 C to 232 C), the widest low-to-high span of any elastomer in this range
  • Clamp torque: 30 in-lb, the elastomeric figure. PTFE takes 50
  • Compliance: platinum cured, FDA compliant
  • Good on ethanol, with minor effect
  • Excellent on isopropyl, per Cole-Parmer chemical resistance data
  • Severe on butane, propane, heptane, pentane and hexane

N.B. Oler's certification reports are explicit on this point. 3P Certz ECR-200031-R0 states that component seals and gaskets may be PTFE, PEEK, FKM, Buna-N or Viton, and that EPDM, PVC and silicone are not acceptable materials for use in the extraction system. Silicone belongs on a steam or food line, not on a solvent line.

Solvent compatibility, by material

Material Butane Propane Ethanol Heptane Pentane Hexane Isopropyl
Silicone D D B D D D A
PTFE A A A A A A A
Viton (FKM) A A A A A A A
Buna-N A A C A A A B

A excellent, B good with minor effect, C fair and not for continuous use, D severe and not recommended, E no data. From the N.B. Oler Sintered Filter Technical Specifications, Rev. 2026.1, with isopropyl ratings and Buna-N on pentane from Cole-Parmer chemical resistance data.

Which material for which job

Material Temperature Torque Pick it when
Silicone -85 F to 450 F (-65 C to 232 C) 30 in-lb Steam, hot water and food contact. Severe on every hydrocarbon
Viton (FKM) -40 F to 400 F (-40 C to 204 C) 30 in-lb The hydrocarbon default, including isopropyl
Solid PTFE -350 F to 500 F (-212 C to 260 C) 50 in-lb Cold service. Cheapest route to full chemical resistance
PTFE envelope, Viton core -100 F to 400 F (-73 C to 204 C) 50 in-lb PTFE chemistry with spring-back, for joints broken every run
Buna-N -30 F to 250 F (-34 C to 121 C) 30 in-lb Water, food, general sanitary. Cheapest

Replacement

  • Replace every 3 to 6 months regardless of how it looks
  • Replace immediately on any cracking, tearing, splitting or permanent deformation
  • A gasket that has taken a compression set passes a cold leak check and then weeps once the line comes up to pressure. That is why interval beats inspection on a gasket
  • Full comparison: Choosing the right gasket material for tri-clamp connections

Stocked in Bend, Oregon.

STOCKED, NOT BUILTStocked by N.B. Oler and built by its manufacturer.
FITSSteam, hot water and food contact lines, in 1, 1.5, 2, 4 and 6 inch tri-clamp. Does NOT fit hydrocarbon extraction service: silicone rates severe against butane, propane, heptane, pentane and hexane, and 3P Certz ECR-200031-R0 names it an unacceptable material for the extraction system. Cole-Parmer rates silicone excellent on isopropyl, but for a solvent line, including isopropyl, use Viton. For cold service use PTFE. Torque to 30 in-lb.

▦ IN YOUR MANUAL

This part appears in the operator manual that ships with your system. The QR code there links to this page.

◈ REFERENCE FOR THIS PART

Choosing the Right Gasket Material for Tri-Clamp Connections →
Buna-N, Viton and PTFE compared on temperature, chemical compatibility and cost
Chemical Compatibility: Seals, Gaskets and Stainless →
Silicone rates D against butane, propane, hexane and pentane, so this is not a solvent gasket
Tri-Clamp Pressure Ratings by Clamp Style and Size →
What the joint this gasket seals is rated to, by clamp style and size
Sintered Filter Technical Specifications →
The chemical compatibility table this page draws from

COMMON QUESTIONS

Can I use silicone on my extraction system?

No. Silicone rates severe against butane, propane, heptane, pentane and hexane, and 3P Certz ECR-200031-R0 names silicone as not acceptable for seals or gaskets in the extraction system. Cole-Parmer rates it excellent on isopropyl, but use Viton for solvent service, including isopropyl, and PTFE for cold service.

What is silicone good for?

Steam, hot water and food contact. Its temperature span, -85 F to 450 F (-65 C to 232 C), is wider than any other elastomer we sell.

What torque?

30 in-lb, the elastomeric figure. PTFE takes 50.

How often should these be replaced?

Every 3 to 6 months regardless of appearance, and immediately on any cracking, tearing, splitting or permanent deformation.